Here we have the Megasquirt 1 V3 which is todate my most popular Megasquirt  it can read most trigger wheels, most commen types are 36-1 Ford etc and 60-2 VW and Vauxhall etc, and VR or Hall sensors, usually modified  with 2 coil driver so you can drive your Coil Pack direct no Module in wasted spark mode, wasted spark mode means you are firing 2 cycls at exactly the same time ie 1&4 and 2&3 in a 4 cycl engine, cycl 1 will be on power and cycl 4 on exhaust stroke, ( the most popular Coil Pack is the Ford Edis one in either 4-6 or 8 cycl ) most Coil Pack are suitable but as I have not tested I can not be 100% sure so test yours and more than likely it will be fine, to drive a 6 cycl you will need 3 Coil Driver, and for an 8 cycl you will need 4 Coil Drivers, also when you drive your Coil Packs direct you can then  use the onboard Rev limiting facility on Megasquirt to cut fuel and spark in a controlled way so you have a soft limit and a hard limit which you can set to what ever you like to suit your engine, and it can also run the Ford Edis (EDIS = Coil Pack and Module) system if you have a 36-1 trigger wheel, it can read most trigger wheels 36-1 and 60-2 being the most popular OE types with VR or Hall sensors, so you can mod to run Coil Packs or Coil on Plugs (COP's) you can even mod to run Sequential Ignition, can also be modified to control cooling fan, flat shift, launch control, dual fuel maps, water injection, Rev counter,or anything that can be switched by a relay.

BTT

So if you are thinking about buying then what I and you need to know is how many cycls you have, what trigger wheel and sensor you have, and what type of Ign you have ie coil pack or coil on plugs.

For a basic setup you will also need water and air temp sensors ( GM ones are ideal) others you will need to alter some resistors to match, aThrottle Position sensor ( make sure it is a potenteometer type not just an on off type).

If you are going to do most of the tuning yourself then a Wideband Controller and sensor is a great help such as Inovate LC1, but there are lots of other makes that will do the job.


To help you choose which MS here is a link so you can compare the differences between MS1, MS2, and MS3

http://www.msextra.com/feature-xref.html


To Pay all you have to do is log on to www.paypal.co.uk and pay sales@megasquirtuk.co.uk Thanks.

BTT

Col1
                                      

   Megasquirt 1 V3

MS 1 V3


To order or pay for items we accept Paypal which is a secure

way to pay and


they accept most Credit Cards, or you can pay by direct Bank Transfer, or you can pay by cheque.

To Pay all you have to do is log on to www.paypal.co.uk and pay sales@megasquirtuk.co.uk Thanks.

BTT

MS 1 V3 Unassembled Kit £295.00

MS 1 V3 Fully assembled, comes with a resonable MAP to get you up and running, wiring diagram you can download from this site (Link), DB37 Plug, and DB9 cable to connect to your pc, Price £365.00 + and Shipping + VAT.

MS 1 V 3 Extra Code 2.5 Bar MAP sensor, good for normally aspirated or Boosted Engines to 30psi max, modified to run the Ford Edis module and coil pack so will run a 4,6 or 8 cycl wasted spark + your Fuel Injection, comes with a resonable MAP to get you up and running, wiring diagram you can download from this site (Link), DB37 Plug, and DB9 cable to connect to your pc, Price £395.00 + and Shipping + VAT.

BTT


MS 1 V 3 Extra Code 2.5 bar MAP sensor, good for normally aspirated or Boosted Engines to 30psi max, and fitted with 2 coil drivers so will run a 4 cycl wasted spark, this is the recommended way as you have complete control of the timing and can also use the onboard rev limiting facility, + your Fuel Injection,comes with a resonable MAP to get you up and running, wiring diagram you can download from this site (Link), DB37 Plug, and DB9 cable to connect to your pc, Price £410.00 + and Shipping + VAT.

MS 1 V 3 Extra Code 2.5 bar MAP sensor, good for normally aspirated or Boosted Engines to 30psi max, and fitted with 3 coil drivers so will run a 6 cycl wasted spark, this is the recommended way as you have complete control of the timing and can also use the onboard rev limiting facility, + your Fuel Injection,comes with a resonable MAP to get you up and running, wiring diagram you can download from this site (Link), DB37 Plug, and DB9 cable to connect to your pc, Price £425.00 + and Shipping + VAT.

ms1v3-3coil-drivers

Here is a Megasquirt running my MX5 Eunos 1990 1600 NA notice the nice short adaptor cable to plug straight into your OE loom.

Adapter Cable to suit above Eunos 1600cc 1990 this allows you to remove OE ECU and insert OE loom plugs to one end and Megasquirt DB37 to the other end, also includes a short Jumper to insert to MAF plug so you can drive yor Fuel Pump through the Adapter cable, £125.00 + Shipping +VAT

Or if you want to make your own I can supply the 76 pin socket for £25 + VAT


 MX5 MS1 V3 extra in car

1990-1997 Mazda Miata, or later models by swapping in the 90-97 CAS

Level of control:  Full Standalone EMS-- Fuel and Ignition Control


Mazda MX5, Miata, Eunos.Megasquirt 1 V3 Extra code loaded, fully assembled, 2.5 bar MAP sensor,  good for normally aspirated or Boosted Engines to 30psi max, due to popular demand I have now got all the mods done to run the CAS system and the OE coils + your Fuel Injection,so all you have to do is wire it in and tune, comes with a resonable MAP to get you up and running, wiring diagram you can download from this site (Link), DB37 Plug, and DB9 cable to connect to your pc, Price £445.00 + Shipping + VAT

Here is a good link to help with the wiring http://www.miataturbo.net/useful-saved-posts-8/how-make-install-

your-own-diy-megasquirt-13676/ 

BTT

Megasquirt 1 V3.0 Extra Code loaded, fully assembled, 2.5 Bar Map Sensor,  good for normally aspirated or Boosted Engines to 30psi max has got 2 Coil Drivers fitted so can run 4 Cycl Cops in wasted spark mode, they are VW 4 wire COPs which are not included, so ideal for your VW Golf or Audi 20 Valve, or as I have also tried the COPs on my Vauxhall 20XE engine, and all run fine looks a lot better than the old coilpack so chuck that old Distributor and coil pack, + your Fuel Injection,comes with a resonable MAP to get you up and running, wiring diagram you can download from this site (Link), DB37 Plug, and DB9 cable to connect to your pc, Price £375.00 + and Shipping + VAT .

Megasquirt 1 V3.0 Extra Code loaded,fully asembled, 3 Bar Map Sensor, good for over 40 PSI boost, has got 2 Coil Drivers fitted so can run 4 Cycl Cops in wasted spark mode, they are VW 4 wire COPs which are not included, so ideal for your VW Golf or Audi 20 Valve. Or as I have also tried the COPs on my Vauxhall 20XE engine, and all run fine looks a lot better than the old coilpack so chuck that old Distributor and coil pack,+ your Fuel Injection, comes with a resonable MAP to get you up and running, wiring diagram you can download from this site (Link), DB37 Plug, and DB9 cable to connect to your pc, Price £435.00 + and Shipping + VAT.

BTT


Megastim V2.2 Price (Fully Assembled) £95.00 + VAT

As above unassembled Price £75.00 + VAT

Bluetooth Adaptor for your Megasquirt 1,2 or 3 with 1 Mtr Cable to plug straight into your DB9 socket so you can run Shadow Dash on your Android Tablet all set ready to go, Price £65.00 + VAT

Jaws Wideband Controller with a digital display fully assembled Price 245.00 + Shipping and + VAT

BTT

Manifold Air Temp Sensor ( Open Element) with Plug & connectors ( calibrated for MS) Price £27.50 + and Shipping + VAT

Manifold Air temp Sensor (Open Element) not calibrated for MS so you will have to calibrate with Easytherm, Price £22.50 + Shipping + VAT.

CLT or water temp sensor with plug and connectors, closed element type, calibrated for Megasquirt, Price £24.50 + Shipping + VAT

USB Adapter ( That works with Megasquirt) Price £26.50 + and Shipping + VAT.

BTT

5 Foot Labeled Wiring loom ( all labels printed) with DB37 plug already installed and Light Weight Plastic Hood ( so will not damage your MS DB 37 pins when racing on or off road ) Price £115.00 + and Shipping + VAT.

1.5 foot ( 460mm) Wiring Pigtails ( all labels printed) and DB37 Plug with Light weight Plastic Hood ( ideal for racing or off road enviroments) suitable for MS 1, 2 or 3 Price £65.00 + VAT

DB37 Plug with 8 inch Tails ( all labels printed) Price £30.00 + VAT

Or if you want to make your own short or full loom as above I sell the DB37 pin Female solder cups on their own. Price £5.50 each,with solid Metal Hood £6.50, or if you want the light weight plastic hood Price £3.00 each.

BTT

MS 1 Chip Extra Code Loaded Price £58.50 + VAT

MAP Sensor 2.5 Bar Price £25.00 + VAT

MAP Sensor 3 Bar Price £50.00 + VAT

Map sensor 4 Bar Price £95.00 + VAT

BTT

 2 Mtr Beldon Shielded cable Ideal for VR Sensor Price £12.50 + Shipping + VAT

DB9 Serial Cable 2Mtr ( 6ft) Price £7.50 + Shipping + VAT

DB9 Cable for Workshop 5 Mtr Price £12.50 + Shipping + VAT

USB Adapter (that works with Megasquirt) Price £26.50 + Shipping + VAT

BTT

Ignition Coil Driver Kits BIP 373 these are the best ones to use if you are replacing or modifying your Megasquirt 1,2, or 3 Price £21.50 + Shipping + VAT

Good used Coil Packs 4 cycl £45 6 cycl Price  £75.00 + Shipping  + VAT

Good used TPS Price  £45.00 + Shipping + VAT

Good used Bike Injectors Price  £45.00 each + Shipping  + VAT

Aluminium Extrusion to make your own injector rails 4 cycl Price £85.00 + Shipping + VAT

As above for 6 cycl Price £110.00 + Shipping  + VAT

BTT

We also carry a sellection of Bike Throttle Bodies sizes from 32mm to 42mm

We can also Program Blank or Corrupted MS 1 Chips.

Terms: Cash, Postal Orders,Cheques, PayPal. PayPal can accept most Credit/Debit cards, or you can pay by direct Bank Transfer.

To Pay all you have to do is log on to www.paypal.co.uk and pay sales@megasquirtuk.co.uk Thanks.

We can also supply all spares to repair or modify etc.

 Thanks for looking and happy squirting, any questions call or email me . Regards Eddie Walsh

BTT